reelplumber wrote:
Is it possible to show some pics of this tube and method of what your talking about? I am trying to picture this.
Yes, I can! I will shoot the tubes and upload later today.
| Angler | Comment | |||
|---|---|---|---|---|
CaptLeeNoga |
How To Make Quick Release Tubes For Dip/Frame Nets |
Lead | ||
reelplumber wrote: Yes, I can! I will shoot the tubes and upload later today.
Last Edited By: CaptLeeNoga 11/05/10 11:02 AM.
Edited 1 time.
|
||||
|
|
||||
CaptLeeNoga |
#1 | |||
|
Regular clear "3/4"OD [outer diameter] and 1/2" ID [inner diameter] vinyl tubing from any hardware store [get 2 ft and make several 4-5" pieces]
![]() 100lb Mono line (24 inches) weaved thru netting and then closed the 2 ends with a crimp or you can use a knot. ![]() Pull mono line to make sure things "snug" up ![]() Thread the mono line thru the tubing. ![]() Push tubing over net leaving 4 inches of exposed net out the other side. ![]() Take BBQ click lighter. Burn tips of tube to round/smooth out jagged edges to prevent net ripping or chafing. ![]() Mark tube threading direction & your name. ![]() BRING at least 1 or 2 extra. They do fall off if you do not push them far enough up the net. They do get thrown overboard into the river during frenzy dumping.
Last Edited By: CaptLeeNoga 11/22/10 12:15 PM.
Edited 3 times.
|
||||
|
|
||||
Sleepless |
#2 | |||
|
Just a quick comment about the plastic tubing. It is referenced by its inner diameter. Be sure to use 1/2" inner diameter which has an outer diameter of 3/4 inch.
Bob
Titusville
|
||||
|
|
||||
CaptLeeNoga |
#3 | |||
Sleepless wrote: Good point. I was not sure what those marking meant on the tubing. Yes, the OD needs to be 3/4", and the inner 1/2" Great and much needed point Bob! This could have spelled disaster if they got 3/4 "inner".. |
||||
|
|
||||
Sleepless |
#4 | |||
|
Captain Lee, you deserve a big round of applause for your detailed instructions and photographs. I have lived in Florida for about 9 years and for 8 shrimping seasons I have been dumping my dipping nets through the hoop end. You can imagine how many shrimp I have picked up off the boat floor during that time. Like many other members, I often wondered how to modify our nets with the tied sock end. Now we know. So, thank you!!!
Bob
Titusville
|
||||
|
|
||||
CaptLeeNoga |
#5 | |||
Sleepless wrote:My pleasure babe. Many folks "humbug" the need to re-engineer the net with a "quick escape" plug. I prefer the plug method. I can do it the other way but it is so much faster to use the plug method on my boat especially when I dump the guest's net who is standing on the bow. They just swing it over and 30 seconds they are back in the water and never had to get their hands wet. Yup, I am a member of the "shrimp on the deck" club too. I do know how to dump proper to reduce and or stop that. But, it takes to long and to many steps to walk the ballie into the bucket from the hoop side. Me <------------ Impatient. The other benefit, is when we are a few socks from a full pull, those shrimp jump out onto the deck before we dump once the lid is off. Having the plug ending really is an asset to reduce the shrimp splatter on the deck when your bucket is brimming. I use a igloo cooler for the thermal insulation and it is rectangle, a 5 gallon bucket is easier to "hit" top side. But my boat does not have a lot of area [center console, live well out in front of console] and that 30" hoop is a pain to attempt a top side dump. I am so glad to get your feedback. I do not want to cause folks more confusion in the process of trying to sort something out. ![]() Thanks babe. |
||||
|
|
||||